Comparative Study on the Influence of U-Shaped Self-Organizing Production Line Configuration on Capacity

Comparative Study on the Influence of U-Shaped Self-Organizing Production Line Configuration on Capacity
复制标题

U型自组织生产线配置对产能影响的比较研究

DOI:
10.12783/dtmse/ameme2020/35526
复制
发表时间:
2021-04
期刊:
DEStech Transactions on Materials Science and Engineering
影响因子:
--
通讯作者:
Shilong Liao
Shilong Liao
中科院分区:
其他
文献类型:
--
作者:
Wenwen Zhang;Shilong Liao

文献摘要

参考文献

相似文献

U型自组织生产线有三种典型代表,即U型游动、追赶超越、蜂窝斗旅。按照工艺顺序放置的设备,以及设备之间的距离,形成U形生产线配置。前者形成了过程不平衡变量,后者形成了通道宽度变量。为此,设计了以过程不平衡和通道宽度为自变量,以生产线产能为因变量的仿真实验。利用Plant-Simulation®仿真平台获取实验数据并进行验证,结果表明,在相同条件下,ChasingOvertaking能力最高。蜂窝桶旅线和U型游动线的生产能力比CO线低20%以上;在离散系统下,三条自组织生产线不受配置因素的影响。
There are three typical representatives of U-shaped selforganizing production line, namely U-shaped Travelling, ChasingOvertaking, Cellular Bucket Brigade. The equipment, placed according to the process sequence, and the distance between the equipment form a Ushaped production line configuration. The former forms the process imbalance variable, and the latter forms the aisle width variable. For this, a simulation experiment with process imbalance and aisle width as independent variables and production line capacity as dependent variable was designed. The Plant-Simulation® simulation platform was used to obtain experimental data and verify it. The results show that ChasingOvertaking capacity is the highest under the same conditions. The production capacity of Cellular Bucket Brigade line and U-shaped traveling line is lower than that of CO line by more than 20%; and under the discrete system, the three self-organized production lines are not affected by configuration factors.
DOI: 10.1080/00207543.2015.1125033
发表时间: 2016-06
影响因子: 9.2
作者:
Qin Chen;Shilong Liao;ZhongZhen Wu;Shu-ping Yi
通讯作者: Qin Chen;Shilong Liao;ZhongZhen Wu;Shu-ping Yi
DOI: --
发表时间: 2012
期刊: Computer Integrated Manufacturing Systems
影响因子: --
作者:
Gao Qing-xuan
通讯作者: Gao Qing-xuan
DOI: 10.1007/s00170-015-7951-z
发表时间: 2017-10
期刊: The International Journal of Advanced Manufacturing Technology
影响因子: --
作者:
Jian Zhou;Xiaohu Wang;Qin Zhang
通讯作者: Jian Zhou;Xiaohu Wang;Qin Zhang
DOI: --
发表时间: 2011
影响因子: 2.7
作者:
Yun Fong Lim
通讯作者: Yun Fong Lim
DOI: 10.1080/00207543.2016.1190472
发表时间: 2017-05
影响因子: 9.2
作者:
K. Nakade
通讯作者: K. Nakade