Investigation of Texture Formation in Ni-7at.%W Alloy Substrates by Spark Plasma Sintering Technique
Investigation of Texture Formation in Ni-7at.%W Alloy Substrates by Spark Plasma Sintering Technique
复制标题
研究%20of%20纹理%20形成%20in%20Ni-7at.%W%20合金%20基材%20by%20Spark%20等离子%20烧结%20技术
DOI：
10.1109/tasc.2009.2017881
复制
发表时间：
2009-06
影响因子：
1.8
通讯作者：
Zhu, YongHua
中科院分区：
文献类型：
--
作者：
Zhou, MeiLing;Suo, HongLi;Gao, Mangmang;Liu, Min;Ma, Lin;Fan, RuiFen;Zhao, Yue;Zhu, YongHua
在涂层导体的应用中，需要具有高强度和低磁性的尖锐立方体纹理合金衬底。在这个作品中，立方体织构了Ni-7at。以先进的粉末冶金铸锭为原料，采用轧制辅助双轴织构法制备了%W衬底。Ni-7at的制备工艺。用火花等离子烧结（SPS）方法制备了具有尖锐立方体织构的%W带。利用电子背散射衍射（EBSD）分析了Ni-7at中立方体织构成分的含量。在小于10度的错取向角范围内，W带表面达到99.4%。进一步探讨了Ni-7at中立方体织构的形成机理。用EBSD对%W胶带进行了研究。特别注意的是织构成分沿着部分再结晶样品的厚度的差异。
A sharp cube textured alloy substrates with high strength and low magnetism are required in coated conductors' applications. In this work, the cube textured Ni-7at.%W substrates, starting from advanced powder metallurgy ingots followed by Rolling Assisted Biaxially Textured Substrate (RABiTS) method, have been prepared. The fabrication processes of Ni-7at.%W tapes with sharp cube texture by spark plasma sintering(SPS) routes were described. By Electron Back Scattering Diffraction (EBSD) analysis, the percentage of the cube texture component in Ni-7at.%W tape surface is found to reach 99.4% within a misorientation angle smaller than 10deg . Moreover, the formation mechanism of the cube texture in the Ni-7at.%W tape was also investigated by EBSD. Particular attention was focused on the difference of the texture components along the thickness of the partially recrystallized samples.
登录
查看更多内容
影响因子：
1.7
作者：
Yuejin Zhao;H. Suo;Min Liu;Danmin Liu;Yingxiao Zhang;Meiling Zhou
通讯作者：
Yuejin Zhao;H. Suo;Min Liu;Danmin Liu;Yingxiao Zhang;Meiling Zhou
影响因子：
9.4
作者：
Kamikawa, N.;Sakai, T.;Tsuji, N.
通讯作者：
Tsuji, N.
影响因子：
3.6
作者：
R. Teranishi;T. Izumi;Y. Shiohara
通讯作者：
R. Teranishi;T. Izumi;Y. Shiohara
DOI：
10.1016/j.msea.2007.02.087
发表时间：
2007-06
影响因子：
6.4
作者：
P. P. Bhattacharjee-P.;R. Ray
通讯作者：
P. P. Bhattacharjee-P.;R. Ray
DOI：
10.1016/0956-7151(93)90211-a
发表时间：
1993-06-01
期刊：
ACTA METALLURGICA ET MATERIALIA
影响因子：
--
作者：
DUGGAN, BJ;LUCKE, K;LEE, CS
通讯作者：
LEE, CS