Leak tightness of bolted flange gasketed joints and stuffing box packings

众所周知，螺栓连接和阀门失效的主要原因是泄漏。最新的北美调查显示，这两个压力容器部件的泄漏在工业设备产生的逃逸排放总量中占有重要的比例。在这些设备中用作密封元件的垫圈和填料盒填料并不是唯一的原因。在环保意识日益增强和环保法规日益严格的今天，人们的注意力不仅集中在改进密封产品上，还关注于实施更好的设计计算方法，以最大限度地减少工业过程设备的逃逸排放。多年来，虽然目前广泛使用的法兰设计方法的有效性引起了越来越多的质疑，但对于填充盒的设计还没有成文的方法。尽管已经为减少逃逸排放做出了大量努力，但防止泄漏仍然是最大的挑战之一。为了确定泄漏控制参数，必须对螺栓连接中的垫圈或填充盒中的压缩填料的一般性能有一个基本的了解。我们最近对垫片的研究表明，垫片的性能不仅取决于工作条件(压力和温度)，而且还取决于安装垫片的机械部件(刚性、表面几何形状、表面粗糙度)。拟议的研究项目旨在改进垫片并优化其在所使用的设备中的综合性能。其目标是开展螺栓垫片连接的基础研究工作。同时，我们的目标是将所获得的知识扩展到填充盒包装的研究中。尽管应用不同，但纸袋的渗漏流动机理实际上是由类似的参数控制的，如接触压力、表面粗糙度、几何形状、流体类型和温度。这项工作的一个重要部分将致力于开发分析模型和数值有限元模型。这些模型将在实际螺栓衬垫接头和填充盒填料上进行实验验证。

It is well established that the major cause of failure of bolted joints and valves is leakage. The latest North American survey showed that leakage from these two pressure vessel components represents an important amount of the total fugitive emissions produced by industrial equipments. The gaskets and stuffing box packings used as sealing elements in these equipments are not the only parameters to blame. With today's increasing environmental consciousness and strict environmental protection laws, attention has focused not only on improving sealing products, but also implementing better design calculation methods that minimize fugitive emissions from industrial process equipments. While over the years the validity of the current extensively used flange design method has raised increasing inquiries, there is no documented design method for stuffing boxes. Even though a substantial effort has been put towards reducing fugitive emissions, preventing leakage remains one of the biggest challenges. A fundamental understanding of the general behaviour of the gasket in a bolted joint or the compression packing in a stuffing box must be conducted in order to delimit the leakage controlling parameters. Our recent studies on gaskets show that their performance depends not only on the working conditions (pressure and temperature), but also on the mechanical components (rigidity, facing geometry, surface roughness) on which they are mounted. The proposed research project aims at improving gaskets and optimizing their general performance within the equipment they are used. Its objective is to pursue fundamental research work on bolted gasketed joints. In parallel, it is our goal to extend the gained knowledge to the study of stuffing box packings. Although, the application is different, the leakage flow mechanism of pakings is practically controlled by similar parameters such as contact pressure, surface roughness, geometry, type of fluid and temperature. An important part of the work will be devoted to the development of analytical models and numerical FEM models. These models will be validated experimentally on real bolted gasketed joints and stuffing box packings.