Omnidirectional Simple Shear Device

岩土工程领域问题的多样性和复杂性日益增加，要求经济和可持续地使用地质材料（土壤和岩石）和类土材料（例如矿物材料，RC材料，工业副产品，工业和焚烧厂的废物），需要更深入地了解它们的力学行为，如实验所观察到的。尽管在过去的几十年里，科学的努力，模型的发展和验证，以模拟复杂的耦合流体力学响应的多相岩土材料仍然属于最具挑战性的研究领域，在岩土工程，为了实现研究建议的目标，慕尼黑工业大学Zentrum Geotechnik实验能力的扩展，用于全面检查土壤和类土壤材料在循环、交替和动态载荷下的耦合水力-机械特性是必要的。所需设备的重点主要在于研究在受控或监测边界条件下剪切载荷期间的行为。使用新设备进行的实验必须涵盖剪切应变幅度、应力路径、压力和排水条件的大范围，这些与所考虑的不同岩土问题相关。到目前为止，慕尼黑工业大学和巴伐利亚大学的测试设备还不能满足所有这些要求。因此，本申请中描述的测试设备对巴伐利亚州未来的研究具有战略重要性。本赠款申请旨在为计划测试设备的一个组成部分全向简单剪切设备（简称：ODSS设备）提供部分资金。在ODSS装置中，通过控制剪切变形的两个运动学独立方向上的剪切应变或剪切应力来施加循环、交替和动态载荷。该装置允许在中等到大的剪切应变幅度范围内进行研究。测试设施的其他组件包括共振柱装置（简称：RC装置）、循环动态三轴装置（简称：DTX装置）和新的加载系统以及用于在现有测试坑中测试大型模型的测量设备。在RC装置中，可以通过使圆柱形样品进入共振来确定小剪切应变幅范围内的刚度和滞后阻尼。使用DTX设备的检查允许分析与ODSS设备中类似的剪切应变幅度范围。尽管如此，在DTX装置中，应力和应变仅在主方向上施加和测量。使用DTX器械无法实现样本中主方向的旋转，而这是ODSS器械的特征之一。

The increasing diversity and complexity of problems in the field of geotechnical engineering and the claim for an economical and sustainable use of geomaterials (soil and rock) and soil-like materials (e.g. mineral materials, RC-materials, industrial by-products, waste from industry and incineration plants) require a much deeper understanding of their mechanical behaviour, as observed experimentally. Despite of the scientific effort in the last decades, the development and validation of models to simulate the complex coupled hydro-mechanical response of multiphase geomaterials still belongs to the most challenging fields of research in geotechnical engineering.In order to achieve the goals of research proposals, an extension of the experimental capabilities of the Zentrum Geotechnik of the Technical University of Munich for the comprehensive examination of the coupled hydro-mechanical behaviour of soil and soil-like materials under cyclic, alternating and dynamic loadings is imperative. The focus of the required equipment lies primarily on the investigation of the behaviour during shear loadings at either controlled or monitored boundary conditions. The experiments to be carried out with the new equipment have to cover the large range of shear strain amplitudes, stress paths, pressures and drainage conditions, which are relevant for the different geotechnical problems under consideration. So far, the testing equipment available at the Technical University of Munich and at universities in Bavaria does not satisfy all these requirements. Therefore, the testing facility described in this application is of strategic importance for the future research in Bavaria.This grant application aims for the partial funding of an Omnidirectional Simple Shear Device (in short: ODSS-device) which is one component of the planned testing facility. In the ODSS-device, the cyclic, alternating and dynamic loadings is be applied by controlling either the shear strain or the shear stress in two kinematically independent directions of shear deformation. The device allows the investigation in the range of medium to large shear strain amplitude. Further components of the testing facility are a Resonant Column Device (in short: RC-device), a Cyclic Dynamic Triaxial Device (in short: DTX-device) and a new loading system as well as measurement equipment for testing large-scale models in an existing testing pit. In the RC-device, the stiffness and hysteretic damping in the range of small shear strain amplitude can be determined by bringing a cylindrical sample into resonance. The examinations using the DTX-device allow the analysis for a similar range of shear strain amplitudes as in the ODSS-device. Nonetheless, in the DTX-device stress and strain are applied and measured exclusively in the principal directions. The rotation of the principal directions in the sample is not possible using the DTX-device while it is one of the features of the ODSS-device.