课题基金 / 基金详情

Mucosal Thickness of the Denture Foundation after Occlusal Force

Mucosal Thickness of the Denture Foundation after Occlusal Force
咬合力后义齿基底的粘膜厚度
批准号:
05671619
负责人:
SUZUKI Tetsuya
金额:
$1.41万
依托单位国家:
日本
项目类别:
Grant-in-Aid for General Scientific Research (C)
财政年份:
1993
资助国家:
日本
项目状态:
已结题
起止时间:
1993 至 1994

项目摘要

项目成果

SUZUKI Tetsuya的其他基金

相似基金

相关文献

中文摘要
翻译
义齿基托压缩性的检测对义齿的构建具有重要意义。这些区域,特别是舌环区,不应该被义齿过度压迫,对于这些特定的区域通常需要缓解。本研究的目的是研究义齿基托的可压缩性,并确定在特定区域的厚度缓解量。主要研究结果如下:最大咬合力作用下,黏膜厚度平均减少0.3mm左右。在最大咬合力作用下,下颌骨粘膜厚度的下降速率大于上颌。从松解术后粘膜厚度的减少情况来看,重度腭裂患者需要松解0.5mm,中度腭裂患者需要松解0.25 ~ 0.50mm。即使在没有腭裂环的情况下,在尖锐乳头和腭裂正中缝合区域的厚度也应增加0.25mm。
英文摘要
Examining of the compressibility of the denture foundation is very important for construct of a denture. The areas, especially the torus palatinus area, should not be pressured excessively by a denture and relief is usually necessary for such specific areas.The purpose of this study was to investigate the compressibility of the denture foundation and to determine the amount of relief in thickness over the specific areas.The main results were follows :1.Decrease in the mucosal thickness under maximum occlusal force was about 0.3mm in averages.2.Decreasing rate in the mucosal thickness under maximum occlusal force was greater in a mandible than in a maxilla.3.Judging from the decrease in the mucosal thickness by relief procedures, it was found that 0.5mm relief in thickness was necessary in a case of a severe torus palatinus and 0.25-0.50mm relief in a moderate one.4.Even in a case without the existance of torus palatinus, about 0.25mm relief in thicknesss was desirable over the incisive papilla and median palatine suture areas.
期刊论文(0)
专著(0)
科研奖励(0)
会议论文
New developments in functional three-dimensional morphological analysis of removable dental prosthesis
  • 批准号:
    19K10222
  • 项目类别:
    Grant-in-Aid for Scientific Research (C)
  • 资助金额:
    $2.83万
  • 财政年份:
    2019
  • 负责人:
    SUZUKI Tetsuya
  • 依托单位:
A handwritten Japanese historical Kana reprint Support System based on pattern recognition and constraint solving
  • 批准号:
    16K00463
  • 项目类别:
    Grant-in-Aid for Scientific Research (C)
  • 资助金额:
    $2.91万
  • 财政年份:
    2016
  • 负责人:
    SUZUKI Tetsuya
  • 依托单位:
Designing palatal augmentation prosthesis using three-dimensional morphology and functional analyses
  • 批准号:
    15K11151
  • 项目类别:
    Grant-in-Aid for Scientific Research (C)
  • 资助金额:
    $3.0万
  • 财政年份:
    2015
  • 负责人:
    SUZUKI Tetsuya
  • 依托单位:
Development of Risk Evaluation Method in Service Agricultural Pipeline using Non-Destructive Inspection
  • 批准号:
    24580353
  • 项目类别:
    Grant-in-Aid for Scientific Research (C)
  • 资助金额:
    $3.41万
  • 财政年份:
    2012
  • 负责人:
    SUZUKI Tetsuya
  • 依托单位:
海外基金