Fouling and gasification studies

结垢和气化研究

• 批准号: 6856-2010
• 负责人: Watkinson, AlanPaul
• 金额: $ 1.68万
• 依托单位: University of British Columbia
• 依托单位国家: 加拿大
• 项目类别: Discovery Grants Program - Individual
• 财政年份: 2013
• 资助国家: 加拿大
• 起止时间: 2013-01-01 至 2014-12-31
• 项目状态: 已结题
• 来源: https://www.nserc-crsng.gc.ca/ase-oro/Details-Detailles_eng.asp?id=520970
• 关键词: Fouling; gasification; studies

Deposition of solids onto surfaces of heat exchangers and other processing equipment is costly in terms of energy and operating efficiency. If root causes of fouling can be established, operating or design changes can be made to mitigate the problem, reducing energy loss and CO2 emissions. Deposition rates are often controlled by attachment of foulants to the surface, and for a given fluid, hydrodynamics, temperatures and surface properties are all important. Our general objective is therefore to elucidate the working mechanisms of fouling in petroleum and other process streams and to obtain a quantitative expression for the rate of fouling which operators can then use to control fouling. The approach is to use batch reactors for reaction and precipitation studies, followed by measurements of thermal fouling rates in re-circulation flow loops under defined flow and temperature conditions. Effects of process variables on rates and deposit properties are established. Models are used to express results and make predictions of rate behaviour. Detailed characterization of fluids aand deposits is necessary to identify mechanisms. Tools include solvent fractionataion of deposits and fluids, ultimate species analysis, asphaltene floccuation titrations, thermogravimetric analysis, scanning microscopy and the like. Topics coverd in this proposal include the role of iron sulphide formation in coke deposition from sour oil streams, the influence of fluid flow parameters on deposition in the adhesion regime, and the link between coking kinetics and the deposition process in flowing fluids. Continuing research in biomass gasifictaion and pyrolysis is also described.

在热交换器和其它处理设备的表面上沉积固体在能量和操作效率方面是昂贵的。 如果能够确定结垢的根本原因，则可以进行操作或设计更改以缓解问题，从而减少能量损失和CO2排放。 沉积速率通常由附着在表面的污垢控制，对于给定的流体，流体力学，温度和表面性质都很重要。 因此，我们的总体目标是阐明石油和其他工艺流中结垢的工作机制，并获得结垢速率的定量表达式，然后操作员可以使用该表达式来控制结垢。 该方法是使用间歇式反应器的反应和沉淀的研究，然后通过测量在确定的流量和温度条件下的再循环流动回路中的热结垢率。建立了过程变量对速率和存款性质的影响。模型用于表达结果并预测速率行为。 流体和沉积物的详细特征对确定机理是必要的. 工具包括沉积物和流体的溶剂分馏、最终物质分析、沥青质絮凝滴定、热重分析、扫描显微镜等。 本提案涵盖的主题包括含硫原油流中硫化铁形成在焦炭沉积中的作用，流体流动参数对粘附状态下沉积的影响，以及流动流体中焦化动力学和沉积过程之间的联系。 还描述了生物质气化和热解的持续研究。