熱間転造仕上げプラスチック歯車の運転性能に関する研究

热轧成品塑料齿轮运行性能研究

基本信息

  • 批准号:
    07650176
  • 负责人:
  • 金额:
    $ 1.09万
  • 依托单位:
  • 依托单位国家:
    日本
  • 项目类别:
    Grant-in-Aid for General Scientific Research (C)
  • 财政年份:
    1995
  • 资助国家:
    日本
  • 起止时间:
    1995 至 无数据
  • 项目状态:
    已结题

项目摘要

これまでの実験で比較的良好な歯面形状が得られていたダイス歯車歯面温度500K,被加工歯車回転数30rpm,転造荷重30Nとして,まず12s間熱間転造仕上げを施した後,転造荷重を10Nと小さくし歯車回転を反転させてさらに10s間加工して仕上げ加工前後の伝達トルクの変動の様子を調べてみた.その結果,歯面形状はかなり改善されているにもかかわらず,伝達トルク変動の大きさにはほとんど変化は見られなかった.この伝達トルクの変動波形を周波数解析したところ,被加工歯車の軸回転周波数成分が支配的であることがわかった.すなわち,歯面形状が改善されたために伝達トルク変動のかみあい周波数成分は改善されていたにもかかわらず,歯面形状の改善はトルク変動の軸回転周波数成分の改善にはほとんど寄与しておらず,しかもその成分が変動の大きさを決めてしまうほどに支配的であったため,結果として熱間転造仕上げによる伝達トルク変動の軽減の効果が認められなかったのである.この軸回転周波数成分の大きさを決めているのは被加工歯車の偏心量であると考えられる.したがって,射出成形プラスチック歯車を熱間転造仕上げする場合には歯面形状よりもまず偏心量を小さくすることを考えるべきである.そのためには心間距離を固定した加工法が有力であるが,現有の加工装置をそのように改造するのは困難であったため,同じ効果が期待できる転造荷重減少方式の熱間転造仕上げについて検討した.すなわち,心間距離を一定に保って加工した場合初期には大きな荷重を必要とするが加工が進むにつれて必要となる荷重の大きさは小さくなっていくものと考えられるのである.実際に実験を行ってみたところ,負荷経路をうまく選ぶと仕上がり歯面形状もかなり改善できることが明らかになった.しかしながら,伝達トルク変動に関しては若干の改善は認められたが大きな効果は上げられていなかった.その原因は運転試験装置を改善した際に軸平行度などの精度に若干問題が生じ正確な測定ができていなかったことと思われる.そのため,今回回転伝達誤差の測定も行ったが,データの考察はできなかった.一方,粘弾性挙動を考慮した歯車の動力伝達特性解析は順調に進めてきたが,今後実験装置の調整を行いその結果と合わせて考察していく予定である.
The better surface shape was obtained after the surface temperature was 500K, the rotation speed was 30rpm, the load was 30N, and the temperature was adjusted after 12 seconds of hot rolling. As a result, the shape of the tooth surface is improved, and the shape of the tooth surface is improved. The frequency analysis of the dynamic waveform is dominated by the frequency component of the shaft rotation of the machined lathe. The shape of the tooth surface is improved. The frequency component of the tooth surface is improved. The frequency component of the tooth surface is improved. The frequency component of the tooth surface is improved. The results show that the heat transfer rate is higher than that of the heat transfer rate, and the heat transfer rate is higher than that of the heat transfer rate. The amplitude of the cyclic wave number component of the shaft is determined by the eccentricity of the machined tooth. For injection molding, the shape of the tooth surface is small and the eccentricity is small. The processing method of fixing the distance between the centers is very powerful, and the existing processing equipment is difficult to modify, and the results are expected to be improved. The distance between the centers is fixed. In the initial stage of processing, the load is necessary. In the process, the load is necessary. In fact, the load circuit is selected and the shape of the surface is improved. A number of improvements have been made to the quality of the products. The reason for this is that some problems arise in the accuracy of the test device when it is used to improve the parallelism of the axis. This is the first time I've ever seen an error in my life. On the one hand, the viscous behavior is considered. The dynamic characteristics of the vehicle are analyzed. The adjustment of the device in the future is carried out. The results are investigated.

项目成果

期刊论文数量(2)
专著数量(0)
科研奖励数量(0)
会议论文数量(0)
专利数量(0)
Lchiro MORIWAKI: "Viscoelastic Behavior of Plastic Gears for Power Transmission (Fundamental Investigation)" Proceedings of 7th International Power Transmission and Gearing Conference. (発表予定). (1996)
Lchiro MORIWAKI:“动力传输塑料齿轮的粘弹性行为(基础研究)”第七届国际动力传输和齿轮会议论文集(即将发表)。
  • DOI:
  • 发表时间:
  • 期刊:
  • 影响因子:
    0
  • 作者:
  • 通讯作者:
{{ item.title }}
{{ item.translation_title }}
  • DOI:
    {{ item.doi }}
  • 发表时间:
    {{ item.publish_year }}
  • 期刊:
  • 影响因子:
    {{ item.factor }}
  • 作者:
    {{ item.authors }}
  • 通讯作者:
    {{ item.author }}

数据更新时间:{{ journalArticles.updateTime }}

{{ item.title }}
  • 作者:
    {{ item.author }}

数据更新时间:{{ monograph.updateTime }}

{{ item.title }}
  • 作者:
    {{ item.author }}

数据更新时间:{{ sciAawards.updateTime }}

{{ item.title }}
  • 作者:
    {{ item.author }}

数据更新时间:{{ conferencePapers.updateTime }}

{{ item.title }}
  • 作者:
    {{ item.author }}

数据更新时间:{{ patent.updateTime }}

森脇 一郎其他文献

歯形・歯すじ偏差曲線間の相互相関関数による解析 前処理が解析結果に及ぼす影響
利用齿廓与齿导程偏差曲线之间的互相关函数进行分析 预处理对分析结果的影响
  • DOI:
  • 发表时间:
    2022
  • 期刊:
  • 影响因子:
    0
  • 作者:
    山﨑 大輔;射場 大輔;塩田 篤;植田 昌蔵;大久保 光;森脇 一郎
  • 通讯作者:
    森脇 一郎
切欠き付与による接着丸棒の接着強度への影響
缺口对粘合圆棒粘合强度的影响
  • DOI:
  • 发表时间:
    2023
  • 期刊:
  • 影响因子:
    0
  • 作者:
    山﨑 大輔;射場 大輔;塩田 篤;植田 昌蔵;大久保 光;森脇 一郎;小田和広・西野恭輔・竹尾真理華・堤 紀子
  • 通讯作者:
    小田和広・西野恭輔・竹尾真理華・堤 紀子
はすば歯車の歯すじ偏差曲線間の相互相関解析
斜齿轮齿导程偏差曲线互相关分析
  • DOI:
  • 发表时间:
    2021
  • 期刊:
  • 影响因子:
    0
  • 作者:
    山﨑 大輔;射場 大輔;塩田 篤;植田 昌蔵;大久保 光;森脇 一郎;小田和広・西野恭輔・竹尾真理華・堤 紀子;塩田篤,射場大輔,植田昌蔵,森脇一郎,大久保光
  • 通讯作者:
    塩田篤,射場大輔,植田昌蔵,森脇一郎,大久保光
無潤滑-潤滑油環境下における100%セルロースナノファイバー(CNF)成形体のトライボロジー特性
100% 纤维素纳米纤维 (CNF) 压坯在非润滑环境中的摩擦学特性
  • DOI:
  • 发表时间:
    2021
  • 期刊:
  • 影响因子:
    0
  • 作者:
    大久保 光;中江 亮太;射場 大輔;森脇 一郎;山田 和志;佐々木 信也
  • 通讯作者:
    佐々木 信也
界面き裂モデルによる接着端部特異場の評価と付加切欠きによる接着強度の向上
使用界面裂纹模型评估粘合端的奇异场并通过添加凹口提高粘合强度
  • DOI:
  • 发表时间:
    2023
  • 期刊:
  • 影响因子:
    0
  • 作者:
    山﨑 大輔;射場 大輔;塩田 篤;植田 昌蔵;大久保 光;森脇 一郎;小田和広・西野恭輔・竹尾真理華・堤 紀子;塩田篤,射場大輔,植田昌蔵,森脇一郎,大久保光;小田和広
  • 通讯作者:
    小田和広

森脇 一郎的其他文献

{{ item.title }}
{{ item.translation_title }}
  • DOI:
    {{ item.doi }}
  • 发表时间:
    {{ item.publish_year }}
  • 期刊:
  • 影响因子:
    {{ item.factor }}
  • 作者:
    {{ item.authors }}
  • 通讯作者:
    {{ item.author }}

{{ truncateString('森脇 一郎', 18)}}的其他基金

粘弾性挙動を考慮したプラスチック歯車対のかみあい伝達誤差の解析
考虑粘弹性行为的塑料齿轮副啮合传动误差分析
  • 批准号:
    09650164
  • 财政年份:
    1997
  • 资助金额:
    $ 1.09万
  • 项目类别:
    Grant-in-Aid for Scientific Research (C)
プラスチック歯車のかみあい伝達誤差に及ぼす粘弾性挙動の影響
粘弹性行为对塑料齿轮啮合传动误差的影响
  • 批准号:
    08650174
  • 财政年份:
    1996
  • 资助金额:
    $ 1.09万
  • 项目类别:
    Grant-in-Aid for Scientific Research (C)
プラスチック歯車の熱間転造仕上げにおける最適加工条件の選定
塑料齿轮热轧精加工最佳加工条件的选择
  • 批准号:
    06650174
  • 财政年份:
    1994
  • 资助金额:
    $ 1.09万
  • 项目类别:
    Grant-in-Aid for General Scientific Research (C)
プラスチック歯車の熱間転造仕上げのシミュレーションプログラムの開発
塑料齿轮热轧精加工模拟程序的开发
  • 批准号:
    05750145
  • 财政年份:
    1993
  • 资助金额:
    $ 1.09万
  • 项目类别:
    Grant-in-Aid for Encouragement of Young Scientists (A)
プラスチック歯車の熱間転造仕上げにおける仕上り歯形の解析
塑料齿轮热轧精加工成品齿形分析
  • 批准号:
    03750102
  • 财政年份:
    1991
  • 资助金额:
    $ 1.09万
  • 项目类别:
    Grant-in-Aid for Encouragement of Young Scientists (A)
プラスチック歯車の熱間転造仕上げに関する研究
塑料齿轮热轧精加工研究
  • 批准号:
    02750101
  • 财政年份:
    1990
  • 资助金额:
    $ 1.09万
  • 项目类别:
    Grant-in-Aid for Encouragement of Young Scientists (A)
高硬度歯車の転造仕上げに関する研究
高硬度齿轮滚压精加工研究
  • 批准号:
    01750132
  • 财政年份:
    1989
  • 资助金额:
    $ 1.09万
  • 项目类别:
    Grant-in-Aid for Encouragement of Young Scientists (A)

相似海外基金

動力伝達用プラスチック歯車の低騒音化に関する研究
动力传动用塑料齿轮降噪研究
  • 批准号:
    10750110
  • 财政年份:
    1998
  • 资助金额:
    $ 1.09万
  • 项目类别:
    Grant-in-Aid for Encouragement of Young Scientists (A)
粘弾性挙動を考慮したプラスチック歯車対のかみあい伝達誤差の解析
考虑粘弹性行为的塑料齿轮副啮合传动误差分析
  • 批准号:
    09650164
  • 财政年份:
    1997
  • 资助金额:
    $ 1.09万
  • 项目类别:
    Grant-in-Aid for Scientific Research (C)
プラスチック歯車のかみあい伝達誤差に及ぼす粘弾性挙動の影響
粘弹性行为对塑料齿轮啮合传动误差的影响
  • 批准号:
    08650174
  • 财政年份:
    1996
  • 资助金额:
    $ 1.09万
  • 项目类别:
    Grant-in-Aid for Scientific Research (C)
プラスチック歯車の熱間転造仕上げにおける最適加工条件の選定
塑料齿轮热轧精加工最佳加工条件的选择
  • 批准号:
    06650174
  • 财政年份:
    1994
  • 资助金额:
    $ 1.09万
  • 项目类别:
    Grant-in-Aid for General Scientific Research (C)
プラスチック歯車の熱間転造仕上げのシミュレーションプログラムの開発
塑料齿轮热轧精加工模拟程序的开发
  • 批准号:
    05750145
  • 财政年份:
    1993
  • 资助金额:
    $ 1.09万
  • 项目类别:
    Grant-in-Aid for Encouragement of Young Scientists (A)
動力伝達用プラスチック歯車の振動・騒音特性に関する研究
动力传动用塑料齿轮振动与噪声特性研究
  • 批准号:
    04750125
  • 财政年份:
    1992
  • 资助金额:
    $ 1.09万
  • 项目类别:
    Grant-in-Aid for Encouragement of Young Scientists (A)
プラスチック歯車の熱間転造仕上げにおける仕上り歯形の解析
塑料齿轮热轧精加工成品齿形分析
  • 批准号:
    03750102
  • 财政年份:
    1991
  • 资助金额:
    $ 1.09万
  • 项目类别:
    Grant-in-Aid for Encouragement of Young Scientists (A)
新しい自己潤滑性プラスチック歯車の開発に関する研究
新型自润滑塑料齿轮的开发研究
  • 批准号:
    03555034
  • 财政年份:
    1991
  • 资助金额:
    $ 1.09万
  • 项目类别:
    Grant-in-Aid for Developmental Scientific Research (B)
プラスチック歯車の熱間転造仕上げに関する研究
塑料齿轮热轧精加工研究
  • 批准号:
    02750101
  • 财政年份:
    1990
  • 资助金额:
    $ 1.09万
  • 项目类别:
    Grant-in-Aid for Encouragement of Young Scientists (A)
{{ showInfoDetail.title }}

作者:{{ showInfoDetail.author }}

知道了